Special Offers
5 inch/125mm double layer diamond bush hammer tool, plato de bujarda for concrete and stone floor (ABH001-125mm)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Wide Use: For marble, granite and concrete floor grinding and texturing 1. Creates anti-slip finish on granite and marble 2. Remove hard coatings and overlays 3. Surface prep for coatings 4. Quickly expose large aggregate 5. Increase concrete bonding effectiveness
- Adapt To Low Speed Polisher: Makita 9227CB/ 9237CB speed adjustable polisher is suggested for the bush hammer tool. Do not recommend to operate with speed too high, ideally less than 1000 RPM.
- Size: 5 inch double plates, about 4.3 inch high
- Lichi Rollers: 3 rollers, Each roller with 30 pins, coarse lichi finish on surface.
- Replacement Roller and SDS Shank Bush Hammer Available In ACTINTOOL Store
- 6 inch bush hammer plate with 4 rollers is also available in Actintool store
- The bearing is wear item, please replace the broken one. Check the instruction in this website: replace bearing instruction.
Operation Warning
- Working Speed under 1000 RPM.Not recommended for high rpm angle grinder, suggested to install bush hammer on speed adjustable polisher, such as makita9227CB/ 9237CB polisher, suggested speed less than 1000 RPM. 30pins bush hammer roller not suggested for three phase walkbehind grinder, too much pressure can break the bearings inside the roller. For three phase grinder, please use the 45 pins bush hammer roller.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- Adjusting the plates distance for different finish. For double plates bush hammer, we can adjust the distance between two plates to have finer or rougher finish. Enlarge the distance can have rougher finish, on the contrary, finish finer if narrowing the distance.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: For Us Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
6 inch/150mm plate lichi finish diamond bush hammer tool for angle grinder (ABH002-150mm)
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Wide Use: 1.Creates anti-slip finish on granite and marble 2.Remove hard coatings and overlays 3.Surface prep for coatings 4.Quickly expose large aggregate 5.Increase concrete bonding effectiveness
- Adapt To Low Speed Polisher: Makita 9227CB/ 9237CB speed adjustable polisher is suggested for the bush hammer tool. Do not recommend to operate with speed too high, ideally less than 1000 RPM.
- Size: double layer plates, two plates in different size, one 6 inch, the other one 5 inch.
- Roller : 4 rollers, each roller with 30 tips.
- Floor coating removing and surface texturing
- The bearing is wear item, please replace the broken one. Check the instruction in this website: replace bearing instruction.
Operation Warning
- Working Speed under 1000 RPM.Not recommended for high rpm angle grinder, suggested to install bush hammer on speed adjustable polisher, such as makita9227CB/ 9237CB polisher, speed less than 1000 RPM suggested. 30pins bush hammer roller not suggested for three phase walkbehind grinder, too much pressure can break the bearings inside the roller. For three phase grinder, please use the 45 pins bush hammer roller.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- Adjusting the plates distance for different finish. For double plates bush hammer, we can adjust the distance between two plates to have finer or rougher finish. Enlarge the distance can have rougher finish, on the contrary, finish finer if narrowing the distance.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: For Us Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
5 inch/125mm plate tungsten star roller diamond bush hammer tool (ABT003-125mm)
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Functions: 1. Creates anti-slip finish on granite and marble 2. Remove hard coatings and overlays 3. Surface prep for coatings 4. Quickly expose large aggregate 5. Increase concrete bonding effectiveness
- Adapt To Low Speed Polisher: Makita 9227CB/ 9237CB is suggested with speed adjustable. Do not recommend to operate with speed too high, ideally less than 1000 RPM.
- Best for granite and marble floor texturing, create antislip finish on stone surface
- Size: 5 inch double plates
- Roller: 3 rollers, each roller with 2 pcs star blade, one blade with 10 teeth.
- Single 5 inch plate also available in actintool store
- Contact seller to buy replacement roller
- The bearing is wear item, please replace the broken one. Check the instruction in this website: replace bearing instruction.
Operation Warning
- Working Speed under 1000 RPM.Not recommended for high rpm angle grinder, suggested to install bush hammer on low speed polisher, such as makita9227CB/ 9237CB polisher, speed less than 1000 RPM suggested. 30pins bush hammer roller not suggested for three phase walkbehind grinder, too much pressure can break the bearings inside the roller. For three phase grinder, please use the 45 pins bush hammer roller.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- Adjusting the plates distance for different finish. For double plates bush hammer, we can adjust the distance between two plates to have finer or rougher finish. Enlarge the distance can have rougher finish, on the contrary, finish finer if narrowing the distance.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: For Us Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
5 Inch/125mm double plates tungsten roller sandblasting finish bush hammer tool (ABT006-125mm)
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 5 inch single plate sandbasting bush hammer tool for angle grinder or polisher
- Create fine sandblasting finish on stone and concrete surface, mostly used on bathroom floor, stairs for antislip purpose.
- Fit with low speed polisher, suggested RPM less than 1000 RPM. It is dangerous to operate in high speed that cause the damage of roller.
- Super hard tungsten roller with 312 small tips to create fine finish on stone surface
- 3 knurling type rollers installed on a 5 inch plate
- Check actintool store for other coarse finish bush hammer tools
- N.W about 3.7 ibs
- Ship from China warehouse, 1-3 handling days, receive in 5-10 days.
Operation Warning
- Working Speed under 1000 RPM.Not recommended for high rpm angle grinder, suggested to install bush hammer on speed adjustable polisher, such as makita9227CB/ 9237CB polisher, speed less than 1000 RPM suggested. 30pins bush hammer roller not suggested for three phase walkbehind grinder, too much pressure can break the bearings inside the roller. For three phase grinder, please use the 45 pins bush hammer roller.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- Adjusting the plates distance for different finish. For double plates bush hammer, we can adjust the distance between two plates to have finer or rougher finish. Enlarge the distance can have rougher finish, on the contrary, finish finer if narrowing the distance.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: For products not stocked in Us, Ship from China Warehouse in 2 days, normally receive in 5-10 days.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
5 inch single plate 30 tips bush hammer plate, bushing hammer tool concrete (ABSDS026-125M)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 【Fit with low speed polisher】This 5 inch single plate bush hammer can fit with low speed polisher
- 【Agressive Cobalt Teeth】3 pcs rollers on a 5 inch plate, each roller is welded with 30 teeth.
- 【Wide Use】1.Remove laminated concrete, failing overlayments and underlayments 2. Create antislip finish on stone and concrete surface 3. Create 4-5 CSP roughness and increase concrete bonding effectiveness before new coating 4. Expose aggregate quickly for concrete surface preparation.
- 【Size】5 inch plate
- 【Operation Tips】Working speed under 1000 RPM, do not operate with too much pressure, which can stop the roller from running . Rollers is also sold separately in actintool store, you can buy to replace the worned one.
- The bearing is wear item, please replace the broken one. Check the instruction in this website: replace bearing instruction.
Operation Warning
- Working Speed under 1000 RPM. Not recommended for high rpm angle grinder, suggested to install bush hammer on speed adjustable polisher, such as makita9227CB/ 9237CB polisher, speed less than 1000 RPM suggested. 30pins bush hammer roller not suggested for three phase walkbehind grinder, too much pressure can break the bearings inside the roller. For three phase grinder, please use the 45 pins bush hammer roller.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- Adjusting the plates distance for different finish. For double plates bush hammer, we can adjust the distance between two plates to have finer or rougher finish. Enlarge the distance can have rougher finish, on the contrary, finish finer if narrowing the distance.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: For Us Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
SDS max shank 5 inch plate 30 tips bush hammer plate, sds max bushing bit (ABSDS027-125M)
Warning
This is a SDS Max 18mm shank bush hammer bit, not 10mm SDS Plus shank.
Fitting with rotary hammer, it only works in rotary mode and can create less deeper finish on stone and concrete. To dig deeper, please fit the bush hammer tool with low speed polisher, more pressure and low speed ( less than 1000 RPM) can make it more aggressive.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 【Fit with rotary hammer and low speed polisher】This 5 inch bush hammer plate is packed with a 5/8"-11 to SDS Max shank adapter, can fit with rotary hammer or demolition hammer. Taking away the adapter, the bush hammer plate can fit with 5/8"-11 threaded polisher.
- 【Agressive Cobalt Teeth】3 pcs rollers on a 5 inch plate, each roller is welded with 30 teeth.
- 【Wide Use】1.Remove laminated concrete and other heavy coating 2. Create antislip finish on surface 3. Increase concrete bonding effectiveness before new coating
- 【Size】5 inch plate, 9 inch long with shank.
- 【Operation Tips】Rotaion mode only, no impact mode, which can twist the adapter shank.Working speed under 1000 RPM, do not operate with too much pressure, which can stop the roller from running and break the shank. Rollers and shank are sold separately in actintool store, you can buy to replace the worned parts.
- Stocked in us, receive in 5 days after placing order.
- The bearing is wear item, please replace the broken one. Check the instruction in this website: replace bearing instruction.
Warning
This is a SDS Max 18mm shank bush hammer bit, not 10mm SDS Plus shank.
Fitting with rotary hammer, it only works in rotary mode and can create less deeper finish on stone and concrete. To dig deeper, please fit the bush hammer tool with low speed polisher, more pressure and low speed ( less than 1000 RPM) can make it more aggressive.
Shipping And Return
Fast Shipping: For US Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
5 inch /125mm single plate star tungsten roller bush hammer for angle grinder (ABT005-125MM)
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 5 inch single plate star roller bush hammer tool for low speed polisher.
- Create fine pointed finish on stone and concrete surface, mostly used on bathroom floor, stairs for antislip purpose.
- Fit with speed adjustable angle grinder or polisher, suggested RPM less than 1000 RPM
- Hard tungsten roller with 10 tips to create fine finish on stone and concrete surface
- 3 star type rollers installed on a 5 inch plate
- Check actintool store for other coarse finish bush hammer tools
- N.W about 3.7 ibs
- Ship from China warehouse, 1-3 handling days, receive in 5-10 days.
- The bearing is wear item, please replace the broken one. Check the instruction in this website: replace bearing instruction.
Operation Warning
- Working Speed under 1000 RPM.Not recommended for high rpm angle grinder, suggested to install bush hammer on speed adjustable polisher, such as makita9227CB/ 9237CB polisher, speed less than 1000 RPM suggested. 30pins bush hammer roller not suggested for three phase walkbehind grinder, too much pressure can break the bearings inside the roller. For three phase grinder, please use the 45 pins bush hammer roller.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- Adjusting the plates distance for different finish. For double plates bush hammer, we can adjust the distance between two plates to have finer or rougher finish. Enlarge the distance can have rougher finish, on the contrary, finish finer if narrowing the distance.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
- Fast Shipping: For products not stocked in Us, Ship from China Warehouse in 2 days, normally receive in 5-10 days.
- Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
- Payment Safety: All transactions are SSL-protected and guaranteed safe
- Your Privacy: We will never share your information with anyone.
5 inch/125mm knurling tungsten roller sandblasting finish bush hammer tool (ABT004-125mm)
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 5 inch single plate sandbasting bush hammer tool for low speed polisher
- Create fine sandblasting finish on stone and concrete surface, mostly used on bathroom floor, stairs for antislip purpose.
- Fit with speed low speed polisher, suggested RPM less than 1000 RPM
- Super hard tungsten roller with 312 small tips to create fine finish on stone surface
- 3 knurling type rollers installed on a 5 inch plate
- Check actintool store for other coarse finish bush hammer tools
- N.W about 3.7 ibs
- Ship from China warehouse, 1-3 handling days, receive in 5-10 days.
- The bearing is wear item, please replace the broken one. Check the instruction in this website: replace bearing instruction.
Operation Warning
- Working Speed under 1000 RPM.Not recommended for high rpm angle grinder, suggested to install bush hammer on speed adjustable polisher, such as makita9227CB/ 9237CB polisher, speed less than 1000 RPM suggested. 30pins bush hammer roller not suggested for three phase walkbehind grinder, too much pressure can break the bearings inside the roller. For three phase grinder, please use the 45 pins bush hammer roller.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- Adjusting the plates distance for different finish. For double plates bush hammer, we can adjust the distance between two plates to have finer or rougher finish. Enlarge the distance can have rougher finish, on the contrary, finish finer if narrowing the distance.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: For products not stocked in Us, Ship from China Warehouse in 2 days, normally receive in 5-10 days.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
6 inch/150mm tungsten sandblasting finish bush hammer plate for concrete and stone floor grinding (ABT001-150mm)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 6 inch single plate sandbasting bush hammer tool for angle grinder or polisher
- Create fine sandblasting finish on stone and concrete surface, mostly used on bathroom floor, stairs for antislip purpose.
- Fit with speed adjustable angle grinder or polisher, suggested RPM less than 1000 RPM
- Super hard tungsten roller with 312 small tips to create fine finish on stone surface
- 4 knurling type rollers installed on a 5 inch plate
- Check actintool store for other coarse finish bush hammer tools
- N.W about 5 ibs
- Ship from China warehouse, 1-3 handling days, receive in 5-10 days.
- The bearing is wear item, please replace the broken one. Check the instruction in this website: replace bearing instruction.
Operation Warning
- Working Speed under 1000 RPM.Not recommended for high rpm angle grinder, suggested to install bush hammer on speed adjustable polisher, such as makita9227CB/ 9237CB polisher, speed less than 1000 RPM suggested. 30pins bush hammer roller not suggested for three phase walkbehind grinder, too much pressure can break the bearings inside the roller. For three phase grinder, please use the 45 pins bush hammer roller.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- Adjusting the plates distance for different finish. For double plates bush hammer, we can adjust the distance between two plates to have finer or rougher finish. Enlarge the distance can have rougher finish, on the contrary, finish finer if narrowing the distance.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: For products not stocked in Us, Ship from China Warehouse in 2 days, normally receive in 5-10 days.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
6 Inch /150mm tungsten bush hammer plate with 4 star type rollers (ABT002-150mm)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 6 inch single plate star bush hammer tool for low speed polisher.
- Create fine pointed finish on stone and concrete surface, mostly used on bathroom floor, stairs for antislip purpose.
- Fit with low speed polisher, suggested RPM less than 1000 RPM
- Hard tungsten star shape roller with 10 small tips to create fine finish on stone surface
- 4 star type rollers installed on a 5 inch plate
- Check actintool store for other coarse finish bush hammer tools
- N.W about 4.8 ibs
- Ship from China warehouse, 1-3 handling days, receive in 5-10 days.
- The bearing is wear item, please replace the broken one. Check the instruction in this website: replace bearing instruction.
Operation Warning
- Working Speed under 1000 RPM.Not recommended for high rpm angle grinder, suggested to install bush hammer on speed adjustable polisher, such as makita9227CB/ 9237CB polisher, speed less than 1000 RPM suggested. 30pins bush hammer roller not suggested for three phase walkbehind grinder, too much pressure can break the bearings inside the roller. For three phase grinder, please use the 45 pins bush hammer roller.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- Adjusting the plates distance for different finish. For double plates bush hammer, we can adjust the distance between two plates to have finer or rougher finish. Enlarge the distance can have rougher finish, on the contrary, finish finer if narrowing the distance.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: For products not stocked in Us, Ship from China Warehouse in 2 days, normally receive in 5-10 days.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
HTC 270mm bush hammer with 6*45 pins rollers (ABHTC019-270mm)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
- 10 5/8 inch / 270mm bush hammer plate
- Rollers: 6 rollers, each with 45 tips. Roller Size: 45 diameter, 39mm long
- Functions 1.Creates anti-slip finish on granite and marble 2.Remove hard coatings and overlays 3.Surface prep for coatings 4.Quickly expose large aggregate 5.Increase concrete bonding effectiveness
- Fit With SASE PDG 8000, HTC 800, HTC900, HTC1500
- Shipment: 1-3 handing days, normally receive in 10-15 days after placing order
Operation Warning
- Working Speed under 1000 RPM.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: We will dispatch all items in 2 business days from China warehouse, normally receive in 10-15 days after placing order.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
8 Inch/200mm diamond bush hammer Martelinas plate with 4 rollers for concrete floor (ABH003-200mm)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
- Designed for hand polishing machine, used to make bush hammered profile on stone and concrete surface.
- Size: 8 inch plate. Double layer plates
- Roller Qty: 4; Pin Qty: 45 pins
- The connector is packed inside
- Cone shape carbide teeth
- For stone and concrete surface texturing
- Ship from China wareshouse in 1-3 days by UPS, DHL, or Fedex, normally receive in 10-15 days after placing order.
Operation Warning
- Working Speed under 1000 RPM.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: This product stocked in China warehouse, we ship from China warehouse by DHL, Fedex and etc. Normally receive in 10-15 adays after placing orderReturns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Redi lock 30 cone carbide teeth bush hammer roller head for Husqvarna grinder (ABR005)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Bush hammer replacement roller HUS grinder. Suitable for one phase grinder.
- Teeth Qty: 30 tips.
- Pack of 3 pieces, bolts included in package.
- Roller installed with holder
- Durable cone shape carbide teeth
- Only high quality bearing from trusted supplier are used in the roller, but the bearing is still wear item, please replace the broken one when necessary.
- Create CSP 4 finish on concrete surface, to increase the bonding effectiveness and expose aggregate quickly for concrete surface preparation.
Operation Warning
- Working Speed under 1000 RPM.Not recommended for high rpm angle grinder, suggested to install bush hammer on speed adjustable angle grinder, such as makita9227CB/ 9237CB polisher, speed less than 1000 RPM suggested. 30pins bush hammer roller not suggested for three phase walkbehind grinder, too much pressure can break the bearings inside the roller. For three phase grinder, please use the 45 pins bush hammer roller.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- Adjusting the plates distance for different finish. For double plates bush hammer, we can adjust the distance between two plates to have finer or rougher finish. Enlarge the distance can have rougher finish, on the contrary, finish finer if narrowing the distance.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: For Us Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
240mm/9.5 Inch Lichi Roller Bush Hammer Plate For Diamatic Grinder (ABDIA023-240mm)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
- 9.5 Inch/240mm bush hammer plate for husqvarna grinder
- Roller：3*45tips Lichi roller, 45mm diameter, 39mm long
- Functions 1.Creates anti-slip finish on granite and marble 2.Remove hard coatings and overlays 3.Surface prep for coatings 4.Quickly expose large aggregate 5.Increase concrete bonding effectiveness
- N.W: 4.13kg
- Shipment: ship in 2 business days, normally receive in 10-15 days after placing order
Operation Warning
- Working Speed under 1000 RPM.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: We will dispatch all items in 2 business days from China warehouse, normally receive in 10-15 days after placing order.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Trapezoid bush hammer grinding disc for SASE grinder (ABR036)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Only for one phase grinder, not suggested for three phase machine
- Teeth Qty: 30 tips
- Pack of 3 pieces
- Qualified bearing guranteed
- Durable Cone shape carbide teeth
- Fit with SASE quick change floor grinder
- Increase bonding effectiveness by preparing the concrete with CSP 4-5 roughness before the application of high build coating and overlays.
- Expose large aggregate quickly for concrete preparation.
Shipping And Return
Fast Shipping: We ship from China warehouse by DHL, Fedex and etc. Customers normally receive in 10-15-10 days.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Trapezoid bush hammer grinding shoes for STI grinder (ABR035)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Only for one phase grinder, not suggested for three phase machine
- Teeth Qty: 30 tips
- Pack of 3 pieces
- Qualified bearing guranteed
- Durable Cone shape carbide teeth
- FIt with STI one phase floor grinder
- Increase bonding effectiveness by preparing the concrete with CSP 4-5 roughness before the application of high build coating and overlays.
- Expose large aggregate quickly for concrete preparation.
Shipping And Return
Fast Shipping: We ship from China warehouse by DHL, Fedex and etc. Customers normally receive in 10-15 days.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
trapezoid bush hammer grinding shoes for Lavina grinder ( Pack of 3) (ABR003)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Only for one phase grinder, not suggested for three phase machine
- Teeth Qty: 30 tips
- Pack of 3 pieces
- Only high quality bearing from trusted supplier are used in the roller, but the bearing is wear item, please replace the broken one when necessary. Please check the bearing replacement instruction here.
- Create CSP 4 finish on concrete surface, to increase the bonding effectiveness and expose aggregate quickly for concrete surface preparation.
Shipping And Return
Fast Shipping: We ship from US warehouse in 2 days. Customer can receive in 5 days.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
9MM non threaded hole 30 cone carbides trapezoid bush hammer grinding shoes for ASL grinder (ABR002)
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Only for one phase grinder, not suggested for three phase machine
- Teeth Qty: 30 tips
- Pack of 3 pieces
- Qualified bearing guranteed
- Durable Cone shape carbide teeth
- Fit with ASL, Iron Horse, Warrior floor grinder
- Increase bonding effectiveness by preparing the concrete with CSP 4-5 roughness before the application of high build coating and overlays.
- Expose large aggregate quickly for concrete preparation.
Shipping And Return
Fast Shipping: We ship from China warehouse by DHL, Fedex and etc. Customers normally receive in 10-15 days.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
HTC 270mm bush hammer with 3*45 pins rollers (ABHTC019-270mm)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
- 10 5/8 inch / 270mm bush hammer plate for HTC grinder
- Fit With SASE PDG 8000, HTC 800, HTC900, HTC1500
- Rollers: 3 rollers, each with 45 tips. Roller Size: 45 diameter, 39mm long
- Functions 1.Creates anti-slip finish on granite and marble 2.Remove hard coatings and overlays 3.Surface prep for coatings 4.Quickly expose large aggregate 5.Increase concrete bonding effectiveness
- Shipment: 2-3 handing days', normally receive in 10-15 days after placing order
Operation Warning
- Working Speed under 1000 RPM.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: We will dispatch all items in 2 business days from China warehouse, normally receive in 10-15 days after placing order.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Klindex 240mm /9.5 inch Bush Hammer Plate (ABKLD024-240mm)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
- 9.5 Inch/240mm bush hammer plate for Klindex grinder
- Roller：3*45tips Lichi roller, 45mm diameter, 39mm long
- Functions 1.Creates anti-slip finish on granite and marble 2.Remove hard coatings and overlays 3.Surface prep for coatings 4.Quickly expose large aggregate 5.Increase concrete bonding effectiveness
- N.W: 4.35kg
- Shipment: ship in 2 business days, normally receive in 10-15 days after placing order.
Operation Warning
- Working Speed under 1000 RPM.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: We will dispatch all items in 2 business days from China warehouse, normally receive in 10-15 days after placing order.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
M6 threaded trapezoid bush hammer grinding shoes, bush hammer replacement roller (ABR004)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Only for one phase grinder, not suggested for three phase machine
- Teeth Qty: 30 tips
- Pack of 3 pieces
- Qualified bearing guranteed
- Durable Cone shape carbide teeth
- Increase bonding effectiveness by preparing the concrete with CSP 4-5 roughness before the application of high build coating and overlays.
- Expose large aggregate quickly for concrete preparation.
- Fit with CPS, Sase , XPS floor grinder.
Shipping And Return
Fast Shipping: We ship from China warehouse by DHL, Fedex and etc. Customers normally receive in 10-15 days.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Husqvarna 270mm/11 Inch 45 Tips Lichi Roller Bush Hammer Plate (ABHUS022-270mm)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Operation Warning
- Working Speed under 1000 RPM.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: We will dispatch all items in 2 business days from China warehouse, normally receive in 10-15 days after placing order.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
30 teeth bush hammer replacement roller (ABR012)
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Replacement roller for 5 inch bush hammer plate sold in ACTINTOOL store
- Teeth Qty: 30 tips. Roller Szie: 22mm long, 34mm diamater
- Pack of 3 pieces, bolts included in package.
- Roller installed with holder
- Durable cone shape carbide teeth
Operation Warning
- Working Speed under 1000 RPM.Not recommended for high rpm angle grinder, suggested to install bush hammer on speed adjustable angle grinder, such as makita9227CB/ 9237CB polisher, speed less than 1000 RPM suggested. 30pins bush hammer roller not suggested for three phase walkbehind grinder, too much pressure can break the bearings inside the roller. For three phase grinder, please use the 45 pins bush hammer roller.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- Adjusting the plates distance for different finish. For double plates bush hammer, we can adjust the distance between two plates to have finer or rougher finish. Enlarge the distance can have rougher finish, on the contrary, finish finer if narrowing the distance.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: For Us Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
45 teeth tungsten cone teeth bush hammer replacement roller for Husqvarna grinder (Pack Of 3 ) (ABR014)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Bush hammer replacement roller for Frankfurt, HTC and HUS grinder. Suitable for powerful three phase grinder.
- Teeth Qty: 45 tips. Roller 5.3cm Long, 4.9cm diameter
- Pack of 3 pieces, bolts included in package.
- Roller installed with holder
- Durable cone shape carbide teeth
Shipping And Return
Fast Shipping: For Us Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Frankfurt 45 teeth bush hammer replacement block, frankfurt 45 tips bush hammer tool for automatic grinding machine ( pack of 3) (ABR011)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Frankfurt 45 pins lichi finish bush hammer tool
- Pack of 3
- 45 teeth on each roller
- Roller 39mm long, 40mm diameter
- Durable cone shape carbide teeth
- Fit with automatic polishing machine
- For stone and concrete surface grinding
Shipping And Return
Fast Shipping: We ship from China warehouse by DHL, Fedex and etc. The estimated delivery time is 10-15 days.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Frankfurt 60 pins Lichi Finish bush hammer tool, frankfurt bush hammer replacement block for automatic machine ( pack of 3) (ABR022)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Frankfurt 60 pins lichi finish bush hammer tool
- Pack of 3
- 60 teeth on each roller
- Roller 54mm long, 50mm diameter
- Durable cone shape carbide teeth
- Fit with automatic polishing machine
- For stone and concrete surface grinding
Shipping And Return
Fast Shipping: We ship from China warehouse by DHL, Fedex and etc. The estimated delivery time is 10-15 days.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
HTC 230mm/9 Inch Lichi Roller Bush Hammer Plate (ABHTC021-230mm)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
- 9 inch bush hammer plate for HTC three phase grinder
- Roller: 3*45 pins roller, 45mm diameter, 39mm long.
- Functions 1.Creates anti-slip finish on granite and marble 2.Remove hard coatings and overlays 3.Surface prep for coatings 4.Quickly expose large aggregate 5.Increase concrete bonding effectiveness
- N.W 4.12 kg
- Shipment: 2-5 days' handing time, normally receive in 15 days after placing order.
Operation Warning
- Working Speed under 1000 RPM.
- Do not apply too much pressure on bush hammer. This will prevent roller from stopping and thus decrease the life span of the carbide tips.
- After each use, please clean up rollers, dry and apply oil to the spindles. It will be ideal to submerge the rollers in oil to prevent spindle rust Roller tips can be re-dressed with diamond blades when they become inefficient.
Shipping And Return
Fast Shipping: We will dispatch all items in 2 business days from China warehouse, normally receive in 10-15 days after placing order.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
5 7/8 Inch SDS Plus shank 4 carbide tip bushing bit, sds bush hammer bit, bushing tool for rotary hammer (ABBT008)
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
Warning
This is a SDS plus 10mm shank bush hammer bit, not 18mm SDS max shank.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- Best for tuckpointing preparation, to rough the old mortar joints to increase the bonding effectiveness for new filling
- SDS Plus 3/8"(10mm) diameter shank bushing tool.
- 5 7/8 inch overall length
- Fit with SDS Plus rotary hammer drill
- Chrome Steel overall shank
- Stocked in us, receive in 5 days after placing order.
Warning
This is a SDS plus 10mm shank bush hammer bit, not 18mm SDS max shank.
Shipping And Return
Fast Shipping: For Us Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
8 Inch SDS Max 4 carbide tip bushing bit, Sds MAX bush hammer bit, bushing tool for rotary hammer (ABBT008)
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
Warning
This is a sds max 18mm shank bushing bit, not 10mm sds plus bit.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 【Mortar Raking Tuckpointing Bit】Best for tuckpointing preparation, for mortar raking and brick removal, to remove old mortar prior to repointing joints, which can increase the bonding effectiveness for new filling
- 【Surface Roughing & Floor Scraping】The welded 4 carbide tips of this versatile sds plus bit can roughen and remove the surface of concrete, mortar, grout and stone. It can also works as a floor scraper for tile, thinset and grout chipping.
- 【Fit With SDS Plus Rotary Hammer】SDS Plus 3/8"(10mm) diameter shank bushing tool, Fit with SDS Plus rotary hammer
- 【Size】8 inch overall length, 1-1/2 inch wide flat bushing bit
- 【Durable One Piece Shank】Chrome steel durable one piece sds plus shank bushing chisel
- 【4Tips Bushing Head】4 pcs cone shape welded teeth, to ceate CSP 4-5 roughness
- Stocked in us, receive in 5 days after placing order.
Warning
This is a sds max 18mm shank bushing bit, not 10mm sds plus bit.
Shipping And Return
Fast Shipping: For Us Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
5 5/8 Inch SDS Plus shank 16 carbide tip bushing bit, sds bush hammer bit, bushing tool for rotary hammer (ABBT006)
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
This is a SDS plus 10mm shank bush hammer bit, not 18mm SDS max shank.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- SDS Plus 3/8"(10mm) diameter shank bushing tool
- Chrome Steel overall shank and durable carbide tips
- 5 5/8 inch overall length, 1-1/4*1-1/4 inch square head
- Fit with SDS Plus rotary hammer drill
- Warning: this is not a 18MM SDS max shank tool
- Stocked in us, receive in 5 days after placing order.
This is a SDS plus 10mm shank bush hammer bit, not 18mm SDS max shank.
Shipping And Return
Fast Shipping: For Us Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
9 1/4 inch SDS Max 16Tips bushing bit for demoliton hammer, overall cut concrete bushing tool head (ABB001)
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- SDS Max 3/4"(18mm) diameter shank bushing tool
- Creating CSP 5 finish on concrete wall and floor.
- Chrome Steel overall cut 16 tips bushing head for demolition hammer
- 9 1/4 inch overall length, 1-1/2*1-1/2 inch square head
- Fit with SDS Max demolition hammer
- Stocked in us, receive in 5 days after placing order.
Shipping And Return
Fast Shipping: For Us Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
14 Inch handheld bushing tool for concrete stone surface, handheld bushing bit bushing hammer tool (ABB005)
• Creating rough CSP 5 similar finish on concrete and stone surface.
• 16*16 durable carbide tips head bushing tool
• Head Size: 1.9*1.9*5 3/8 inch
• High quality durable rubber hand
• N.W: 1.72 KG, about 3.8 ibs heavy hammer
• Stocked in us, receive in 5 days after placing order.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
• 14 inch handheld bush hammer tool• Creating rough CSP 5 similar finish on concrete and stone surface.
• 16*16 durable carbide tips head bushing tool
• Head Size: 1.9*1.9*5 3/8 inch
• High quality durable rubber hand
• N.W: 1.72 KG, about 3.8 ibs heavy hammer
• Stocked in us, receive in 5 days after placing order.
Shipping And Return
Fast Shipping: For Us Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
5" diamond 12 segments turbo cup wheel for concrete grinding (ACW017-5")
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 5" inch turbo cup wheel
- 12 pcs 5mm thick segment , size: 25*8*5mm
- Grit 30/36#
- Excellent for grinding concrete flat
- Fast removal of epoxy, paint and vinyl adhesives that are on concrete
Shipping And Return
Fast Shipping: We will dispatch this items in 2 business days from US warehouseReturns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
4 Inch Diamond Crack Chaser Grinidng Wheel for Concrete, 0.375 Inch Thick Segments Diamond Mortar Joint Raking Blade (ACW021-4")
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query
- 【Concrete Crack Repair & Mortar Joint Remove 】This diamond mortar removal blade is widely used for routing and repairing cracks in concrete, cement, ashphat and stone. It can also works as an aggressive mortar joint removal tool for tuckpointing
- 【5/8-11" Threaded Arbor】This crack chaser blade built with 5/8-11" threaded arbor, fit with your angle grinder without the use of flange.
- 【0.375" V-Shape Crack Width】0.375" thick diamond segment for V shape cutting, each segment 1 5/16" in length and 1/2" in width.
- 【13,000 RPM max】Tuckpointing blade operating no more than 13,000 RPM
- 【Use Wet or Dry】Wet or dry use crack chaser wheel, better with water.
- 【High Quality Diamond】High quality diamond sourced from proffessional supplier
Shipping And Return
Fast Shipping: We will dispatch this items in 2 business days from US warehouseReturns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
4.5 inch 0.375" Thick V Shape Segment Diamond Crack Chaser Blade For Concrete, Mortar Joint Grinding Blade (ACW019-4.5")
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 【Concrete Crack Repair & Mortar Joint Remove 】This diamond mortar removal blade is widely used for routing and repairing cracks in concrete, cement, ashphat and stone. It can also works as an aggressive mortar joint removal tool for tuckpointing
- 【5/8-11" Threaded Arbor】This crack chaser blade built with 5/8-11" threaded arbor, fit with your angle grinder without the use of flange.
- 【0.375" V-Shape Crack Width】0.375" thick diamond segment for V shape cutting, each segment 1 5/16" in length and 1/2" in width.
- 【13,000 RPM max】Tuckpointing blade operating no more than 13,000 RPM
- 【Use Wet or Dry】Wet or dry use crack chaser wheel, better with water.
- 【High Quality Diamond】High quality diamond sourced from proffessional supplier
Shipping And Return
Fast Shipping: We will dispatch this items in 2 business days from US warehouseReturns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
7 inch 0.375" Thick V Shape Segment Diamond Crack Chasing Blade For Concrete, Mortar Joint Removal Tool (ACW020-7")
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 【Concrete Crack Repair & Mortar Joint Remove 】This diamond mortar removal blade is widely used for routing and repairing cracks in concrete, cement, ashphat and stone. It can also works as an aggressive mortar joint removal tool for tuckpointing
- 【5/8-11" Threaded Arbor】This crack chaser blade built with 5/8-11" threaded arbor, fit with your angle grinder without the use of flange.
- 【0.375" V-Shape Crack Width】0.375" thick diamond segment for V shape cutting, each segment 1 5/16" in length and 1/2" in width.
- 【13,000 RPM max】Tuckpointing blade operating no more than 13,000 RPM
- 【Use Wet or Dry】Wet or dry use crack chaser wheel, better with water.
- 【High Quality Diamond】High quality diamond sourced from proffessional supplier
Shipping And Return
Fast Shipping: We will dispatch this items in 2 business days from US warehouseReturns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
7" diamond 24 segments turbo cup wheel for concrete grinding (ACW0002)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 7" inch turbo cup wheel
- 24 pcs 5mm thick segment , size: 25*8*5mm
- Grit 30/36#
- Excellent for grinding concrete flat
- Fast removal of epoxy, paint and vinyl adhesives that are on concrete
Shipping And Return
Fast Shipping: We will dispatch this items in 2 business days from US warehouseReturns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
7" diamond 10 arrow segments cup wheel for concrete grinding (AAS002-7")
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 7" inch arrow segments cup wheel
- Super Thick 10 pcs arrow segments, each segment 9mm thick
- Grit 30/36 #
- Grind down coatings without gumming up like traditional segmented grinding cups do
- Excellent for grinding concrete flat, can also be used for fast removal of epoxy, paint and vinyl adhesives that are on concrete
Shipping And Return
Fast Shipping: We will dispatch this items in 2 business days from US warehouseReturns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Lavina tungsten carbide scraper for the removal of tough mastics glue ( 3 Packs) (AGSR-LAV 002)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
- Tungsten carbide scraper for the aggressive removal of tough and sticky mastics, glue, vct and other pesky coatings without gumming up like traditional metal tools.
- Trapezoid 3*6mm bolt on holder fit with Edco, Bartell, Lavina Onfloor floor grinding machine.
- Pack of 3 pcs
- Replaceable, 4-sided tapered tungsten carbide inserts.
- Right and left ajustable direction
Shipping And Return
Fast Shipping: For Us Customers, we will dispatch in 2 business days from US warehouse. For Customers outside US, we ship from China warehouse by DHL, Fedex and etc.Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Trapezoid redi lock tungsten carbide scraper for the removal of mastics and glue floor( 3 Packs) (AGSR-RLH 010)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
1. Tungsten carbide scraper for the quick and easy removing of rubbery mastic, thick glues and other elastomeric coatings that bush hammer and metal bond toolings will not remove effectively because they will gum up and smear.
2. Pack of 3 pcs
3. Replaceable, 4-sided tapered tungsten carbide inserts.
4. Product stocked in US warehouse. Receive in 5 days after placing order.
5.Right and left ajustable direction
Shipping And Return
Fast Shipping: We will dispatch all items in 2 business days from US warehouseReturns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Tungsten carbide scraper insert replacement for floor grinding tungsten scraper (AGS-TCI-001)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
1. Tungsten carbide scraper for the quick and easy removing of rubbery mastic, thick glues and other elastomeric coatings that bush hammer and metal bond toolings will not remove effectively because they will gum up and smear.
2. Pack of 6 pcs insert and 8 pcs screws.
3. Size 16*16*5mm
4. Tapered 4- sided replaceable tungsten carbide inserts.
5. Customer can choose sea shippment for bulk order, please send email to judy@actintool.com for more info.
Shipping And Return
Fast Shipping: We will dispatch all items in 2 business days from US warehouseReturns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Trapezoid 3*9mm non threaded tungsten carbide scraper for ASL Iron Horse Warrior Floor Grinder (AGS-TS-9mm)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
1. Tungsten carbide scraper for the quick and easy removing of rubbery mastic, thick glues and other elastomeric coatings that bush hammer and metal bond toolings will not remove effectively because they will gum up and smear.
2. Trapezoid 3*9mm non threaded holder fit with ASL, Iron Horse, Warrior Floor Grinder
2. Pack of 3 pcs
3. Replaceable, 4-sided tapered tungsten carbide inserts.
4. Product stocked in US warehouse. Receive in 5 days after placing order.
5.Right and left ajustable direction
Shipping And Return
Fast Shipping: We will dispatch all items in 2 business days from US warehouseReturns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Trapezoid Bolt On 3*M6 threaded carbide cutting glue remover for CPS XPS SASE floor grinder ( 3 Packs) (AMB021-M6)
1. Tungsten carbide scraper for the quick and easy removing of rubbery mastic, thick glues and other elastomeric coatings that bush hammer and metal bond toolings will not remove effectively because they will gum up and smear.
2. Products not in stock, produce after order placed. 3-10 days' production days.
3. Deliver by DHL, UPS or Fedex, 5-7 days' deliver time.
4. Normally receive in 15 days after placing order.
5. Customer can choose sea shippment for bulk order, please send email to judy@actintool.com for more info.
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
2. Products not in stock, produce after order placed. 3-10 days' production days.
3. Deliver by DHL, UPS or Fedex, 5-7 days' deliver time.
4. Normally receive in 15 days after placing order.
5. Customer can choose sea shippment for bulk order, please send email to judy@actintool.com for more info.
Shipping And Return
Fast Shipping: We will dispatch all items in 2 business days from US warehouseReturns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
Core drill bit adapter 5/8"-11 threaded male to sds plus male (ASDA003)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 【5/8"-11 Male To SDS Plus Shank】
- 【Fit with sds plus rotary hammer to connect with 5/8"-11 threaded core drill bit, wire brush and such 】
- 【Industrial Grade Steel】
- 【Do not use this adapter on Hammer Mode, Rotation Mode Only】
- 【Adapter only, bit not included】
Shipping And Return
Fast Shipping: We will dispatch all items in 2 business days from US warehouseReturns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
ACTINTOOL SDS Arbor Adapter, Core Drill Bit Adapter 5/8"-11 Thread Male to SDS Max Shank (ASDA005)
Returns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
For non-US countries, we only ship for orders up to 140 USD. Please send email to judy@actintool.com if there is a query.
- 【5/8"-11 Male To SDS Max Shank】
- 【Fit with sds Max rotary hammer to connect with 5/8"-11 threaded core drill bit, wire brush and such 】
- 【Industrial Grade Steel】7 inch overall length
- 【Do not use this adapter on Hammer Mode, Rotation Mode Only】
- 【Adapter & Pilot Drill Included】
Shipping And Return
Fast Shipping: We will dispatch all items in 2 business days from US warehouseReturns: If your item is faulty or we have sent you something different to what you ordered, return it to us in the original packaging within 30 days and we will give you a replacement or a part refund with shipping cost deducted.
Payment Safety: All transactions are SSL-protected and guaranteed safe
Your Privacy: We will never share your information with anyone.
- 1